發電機組專業術語中英文對照大全（U、V、W、Z）

U

Undershoot

Undershoot refers to the amount by which voltage or frequency drops below the nominal value as the voltage regulator or governor responds to changes in load.

下超調

下超調指電壓調整器或控制器在應對負荷變化時，電壓或頻率低于額定的量。

Utility

The utility is a commercial power source that supplies electrical power to specific facilities from a large central power plant.

市電

市電是商業電源，從大型中央電站向各設施供電。

V

Voltage Control

The voltage control is a rheostat that sets the operating point of the voltage regulator and therefore controls the output voltage of the generator set, within its design limits.

電壓控制

電壓控制是設定電壓調整器的運行點從而在設計范圍內控制發電機組的輸出電壓的變阻器。

Voltage Dip

Voltage dip is the dip in voltage that results when a load is added, occurring before the regulator can correct it, or resulting from the functioning of the voltage regulator to unload an overloaded engine-generator.

電壓暫降

電壓暫降是在負荷增加而調整器還未能進行校正時、或電壓調整器正在為過載的發動機卸載時出現的電壓下降。

Voltage Regulation

Voltage regulation is a measure that states the difference between maximum and minimum steady-state voltage as a percentage of nominal voltage.

電壓調整率

電壓調整率描述的是最大和最小穩態電壓差與額定電壓之間的百分比。

W

Watt-Hour Meter

A watt-hour meter records the total power output at a specific point in a system. Typical recording increment is in kW-hours.

電度表

電度表記錄系統中某一點的總電力輸出，通常以千瓦時為記錄單位。

Wye Connections

A Wye connection is the same as a star connection. It is a method of interconnecting the phases of a three-phase system to form a configuration resembling the letter Y. A fourth (neutral) wire can be connected at the center point.

Y連接

Y連接就是星形連接，也就是把三相系統中的相按照字母Y的形狀連接起來，還可以在中心點接上第四根（中性）線。

Z

Zero Sequence

Zero sequence is a method of ground fault detection that utilizes a sensor (CT) that encircles all the phase conductors as well as the neutral conductors. The sensor will produce an output proportional to the imbalance of ground fault current in the circuit. This output is then measured by a relay to initiate circuit breaker tripping or ground fault alarm.

零序

零序是一種接地故障檢測方法，它使用一個傳感器（CT）來把所有相導體和中性導體連接在一起，傳感器會按照線路中接地故障電流的不平衡程度等比例地產生輸出，再由一臺繼電器來測量這一輸出，并斷開斷路器或釋放接地故障警報。